Advertisement
Product Releases
Subscribe to ECN Magazine Product Releases

Frameless Motors Integrate Rotor Ring to Outside Hub

February 4, 2009 6:44 am | Comments

Presenting a rotor external to the stator, Applimotion’s ULT-O frameless motors enable the integration of the rotor ring into an outside rotating hub. The devices are optimized to run at low speeds in position applications or at high speeds for scanning systems, according to the company. The instruments operate from traditional

POL Converters Deliver 20 Amps

February 4, 2009 6:22 am | Comments

Accepting an input from 2.40 V to 5.50 V or 4.50 V to 14 V, respectively, Lineage Power’s APTH020A0X3-SRZ and APTS020A0X3-SRZ TLynx open-frame DC/DC converters units provide up to 20 A of output current in a regulated output voltage range from 0.60 VDC to 5.50 VDC. Delivering an output from 0.60 VDC to

MicroTCA ATR Chassis Supports Mobile Applications

February 4, 2009 6:00 am | Comments

Compatible with water and water-glycol fluids up to 150 psi, Hybricon’s new 3/4 Tall Long Liquid Cooled MicroTCA ATR is designed to support applications for rugged environments in airborne and ground mobile technology. The architecture holds an 11-slot MicroTCA backplane and a military power supply for MIL-STD-704F aircraft and MIL-STD-1275 vehicle use. The enclosure allows deployment of 0°C-to-55°C temperature range payload

Advertisement

Dual-Core SoC Has Onboard Image Recognition

February 4, 2009 5:13 am | Renesas | Comments

Integrating two SH-4A 32-bit CPU cores on a single chip, the SH7776 (SH-Navi3) system-on-chip (SoC) from Renesas also incorporates on-chip graphics functions and image-recognition processing as well as a 2-D and 3-D graphics processor for improved map rendering and operation screens. Suitable for applications such as next-generation high-performance car information terminals, the device performs at 1,920 MIPS at 533 MHz and can execute multiple external environment recognition programs

Super Flux LEDs Target Automotive PCBs

February 4, 2009 4:52 am | Comments

Replacing the MAKO product family, Bivar’s ORCA Series super flux LEDs are designed for use on standard printed circuit boards (PCBs) for the automotive industry. The 7.6-mm² devices offer dome, oval, and flat lens geometries to provide viewing angles of 30°, 45°, 80°, and 160°. The components shine in red, green, blue, yellow, and

Current-to-Digital Converter Enables Image Capturing in CT Systems

February 4, 2009 4:36 am | Analog Devices, Inc. | Comments

Offering 128 data conversion channels, Analog Devices’ ADAS1128 24-bit current-to-digital converter allows high-slice-count CT systems to capture real-time moving images, such as a beating heart. The 10-mm × 10-mm mini BGA-packaged unit exhibits sample rates of up to 20 ksps (50-µs integration time), simultaneous sampling, noise down to 0.4 fC, and power dissipation of 4.5 mW/channel at full speed. All converted

Enclosure Serves Military Airborne Applications

February 3, 2009 12:08 pm | Comments

Measuring 19” H × 25” D × 17” W and weighing 56 lbs, One Stop Systems’ OSS-ENCL-11U-1866 11U ruggedized system enclosure targets military and airborne applications. The solid seam-welded aluminum unit contains a 3U 15-slot

Diffuse Mode Sensors Evaluate Welding Caps

February 3, 2009 6:16 am | Comments

Detecting faults including inclusion, faulty dressing, or burrs, Pepperl+Fuchs’ WTS10 diffuse mode sensors provide non-contact evaluation of the quality of welding cap fronts. The devices check upper and lower welding caps simultaneously and present pre-fault (near the limit) indication for proactive maintenance. The units offer a scratch-resistant mineral glass lens, position tolerance of ±2 mm, tilt angle tolerance of ±1.5°, coaxial optics with

Advertisement

LED Drivers Supply High Output Current

February 3, 2009 5:54 am | Comments

Boasting output current accuracy of up to ±2%, Aimtec's AMLD-IZ and AMLDL-Z Series step-down DC/DC LED drivers (SSLDs) offer standard output currents of 300 mA, 350 mA, 500 mA, 600 mA, and 700 mA. The DIP24- or DIP14-packaged units present input ranges from 5 VDC to 36 VDC and 7 VDC to 30 VDC, a remote

Brushless Motor Includes Integral Controller

February 3, 2009 5:31 am | Comments

Designed with an integral controller, the Motomate Brushless Motor from Crouzet is intended for applications where programmable movement of simple mechanisms is required. The brushless motor features efficiency of 90%, and motor range of 30 W or 80 W. Motomate produces up to 0.3 N.m in the direct drive configuration

VCXOs Function over Wide Frequency Range

February 3, 2009 5:28 am | Comments

Adding to the XpressO oscillator series, Fox Electronics’ FVXO-PC72 2.5-V LVPECL VCXOs perform in a frequency range from 0.7500 MHz to 1 GHz. The 7-mm × 5-mm components employ a family of proprietary application specific integrated circuits (ASICs), as well as a third order Delta Sigma Modulator (DSM). The devices offer

PMC Card Offloads Host Processing Tasks

February 3, 2009 5:22 am | Comments

The SPMC/DPMC-214 rugged PMC card from Curtiss-Wright offloads host processor cards from CANbus, MilCAN, and Utility Bus processing tasks. Available in both air- and conduction-cooled versions, the PMC card provides 4 CANBus ports or 4 MilCAN ports, along with the US Army standard Utility Bus

WiMedia-Based Multiband Validation Software is Most Automated

February 3, 2009 5:02 am | Keysight Technologies | Comments

Able to work with Infiniium Series oscilloscopes, Agilent’s WiMedia-based multiband orthogonal frequency domain modulation ultra-wideband validation software can make measurements with via connection to the SMA input or by attaching the receiver antenna directly to the input of the oscilloscope for radiated testing.

Advertisement

Microwave Transistors Serve Telecom Applications

February 3, 2009 4:57 am | Comments

Coming in industry-standard ceramic-metal packages, Cree's CGH21120F and CGH25120F GaN HEMT microwave transistors perform in telecommunication applications, such as W-CDMA, LTE and WiMAX. The components consist of single, input-pre-matched GaN HEMT devices providing >120 W. The CGH21120F is designed for

Universal Control Module Uses Resistive Touchscreen

February 3, 2009 4:16 am | Comments

Designed for the food service industry, Renau Electronic Laboratories’ UCM-1000 universal control module utilizes a 4.3” WQVGA TFT color resistive touchscreen. The 5.25” W × 3.45” H × 0.90” D unit connects to Renau’s Hybrid Micro Control Series process controllers via Renau’s Single Wire Communication Network. The touchscreen

Pages

X
You may login with either your assigned username or your e-mail address.
The password field is case sensitive.
Loading