Advertisement
Product Releases
Subscribe to ECN Magazine Product Releases

I/O Module Digitally Expands SBCs

October 31, 2008 6:07 am | Comments

Designed for expansion on Pico-ITXe SBCs, the PCO-UIO48-G from WinSystems is a 48-point digital I/O interface with interruptible event sense. The module can monitor 24 of the rising and falling digital edge transitions, latch them, and then signal the host processor that a change of input status has occurred. Each I/O line is programmable for input, output, or output

DC/DC Converters Present Wide Output Range

October 31, 2008 5:47 am | Comments

Operating over an input range from 4.500 V to 13.800 V, Bel Power’s Micro SIP Series non-isolated DC/DC converters demonstrate an output voltage trim range from 0.590 VDC to 5.100 VDC. The RoHS-compliant devices offer efficiencies of up to 91%, a fixed switching frequency of 500 kHz, and protections including differential remote on/off, under-voltage

Design Platform Creates Displays

October 31, 2008 5:12 am | Comments

Having a layer of colored oil operating as an optical shutter, Liquavista’s ColorBright Liquidizer electrowetting design platform makes displays by generating a transparent channel to give selectable views of reflector designs and effects. The tool exhibits defining of segment shapes within the colored oil active area, selective fill, and a “hidden until ON” function to have the display match the color of the product casing until activated. The segmented cells offer reflectance of 40%, a contrast ratio of

Advertisement

Chipsets Combine Transceiver and Beamforming

October 30, 2008 12:16 pm | Comments

Using vector mesh networking, Quantenna Communications’ QHS1000, QHS600, and QHS450 802.11n WLAN chipsets integrate a 4x4 MIMO radio/transceiver and Tx beamforming. The devices support real-time video transmission over the 5 GHz band and data over the 2.4 GHz band. The components integrate power amplifiers (PAs) with 18 dBm output power, a low-noise amplifier (LNA), video graphics array (VGA), switches, baluns, and diplexers. The QHS1000 offers up to

VHF-Band VCO Yields Low Phase Noise

October 30, 2008 11:43 am | Comments

Performing from 284 MHz to 294 MHz with a tuning voltage range from 0.30 VDC to 3 VDC, Z-Communications’ SMV0290A-LF VHF-band VCO exhibits a typical phase noise of -118 dBc/Hz at an offset of 10 KHz. The 0.30” × 0.30” × 0.08” SUB-L-packaged component delivers a typical output power of -1 dBm from a 3.30 VDC supply while drawing 17 mA (typ.) over

Vent Panel Prevents Fire from Spreading

October 30, 2008 11:12 am | Comments

Using a flame-retardant coating to expand and close honeycomb cells, Universal Air Filter’s PyroCide honeycomb vent panel keep fires that start within an electronics chassis from spreading any further. The component utilizes >95% open area for negligible resistance to air flow within an electronics cooling chassis in telecom and datacom equipment designed to meet

Frequency Inverter Employs Internal Disconnect Switch

October 30, 2008 10:37 am | Comments

Removing power to facilitate service and maintenance, Lenze-AC Tech’s SMVector NEMA 4X-enclosed frequency inverter utilizes an internal disconnect switch. The device presents a run/stop digital input, 3 programmable digital inputs (4 for 15 hp models or higher), a Form A relay, an open collector, an analog voltage input and output from 0 VDC to 10 VDC, and an analog current input from

Touchscreen Uses Projected Capacitive Touch

October 30, 2008 10:08 am | Ocular, Inc. | Comments

Showing no film deformations over time, Ocular’s Crystal Touch all-glass projected capacitive touchscreen works using a finger, styli, or a thin glove with the optical quality of a TFT or monochrome display. The scratch-resistant device exhibits auto calibration, a power input of 3 V, resolution of 3 million pixels max., operating temperature from -20°C to 75°C, storage temperature from

Advertisement

Connectors Fit in PCIe Architectures

October 30, 2008 9:37 am | Comments

Acting as point-to-point full duplex I/O bus connectors, ERNI Electronics’ X1, X4, X8, and X16 right-angled card edge connectors meet the requirements of PCIe architectures. The 1 mm centerline family provides board-to-board distances from 5.84 mm to 16.68 mm, compatibility with 1.6 mm to 2.4 mm thick motherboards and 1.6 mm thick daughter cards, and stack heights of

Switches Perform in Harsh Environments

October 30, 2008 9:02 am | Comments

Meeting IP67, IEC60529, UL94V-0, UL 1015, and CSA TEW 105 standards, NKK Switches’ WT, WR, and WB Series environmentally-sealed switches operate in refrigeration equipment, AC motor control, monitoring equipment, biomedical instrumentation, and boating applications. The single- and double-pole WT toggles exhibit current ratings of 10 A at 125 VAC or 30 VDC and 6 A at 250 VAC, min. mechanical life of 30,000 operations, min. electrical life of 15,000 operations, and

TOPICS:

Servo Interface Includes 8 DAC Channels

October 30, 2008 7:25 am | Comments

Functioning in motion control applications, Mesa Electronics’ 7I65 8-axis analog servo interface works with 8 16-bit DAC channels. The component presents 8 TTL or differential encoder inputs, 8 12-bit + sign A-D inputs, 8 isolated motor enable outputs, and 4 isolated digital inputs. Analog outputs have software selectable ranges including -10 V to 10 V, -5 V to 5 V, 0 V to 5 V, and

UPS Power Ratings Extend to 1,100 kVA

October 30, 2008 7:25 am | Comments

Eaton Corporation extended the power ratings for its 9395 uninterruptible power system (UPS) to 1100 kVA. The 9395 System Bypass Module (SBM) makes it possible to parallel UPSs with non-identical kVA ratings. The 1100 kVA UPS, part of the Powerware series, is an extension of the 825 kVA system. The SBM technology has the capability to parallel up to 32 power modules

FPGA Families Support High RLDRAM Rates

October 30, 2008 6:58 am | Comments

The LatticeSC and LatticeSCM FPGA families (collectively, the “LatticeSC/M” families) support RLDRAM I/II rates up to 800 Mbps. The high-speed RLDRAM I and RLDRAM II memory controller IP (intellectual property) is implemented in Lattice’s low-power MACO (Masked Array for Cost Optimization) structured ASIC technology. The FPGAs are fabricated on Fujitsu’s 90 nm CMOS process technology

Advertisement

Terminal Blocks Operate in Wide Capacitance Range

October 30, 2008 6:30 am | Comments

Protecting the filter elements during installation and field service, Spectrum Control’s 30 A barrier strip terminal blocks illustrate capacitance from 2,500 pF to 5,200 pF. The UL-recognized and CSA-approved devices perform over a temperature range from -55°C to 105°C over a 100 VDC working voltage with from 2 to 6 terminals for soldering or spade lugs. The components perform in

Protection Array Provides Low Capacitance

October 30, 2008 5:49 am | Comments

Exhibiting a surge current of >11 A, Vishay Intertechnology’s VBUS054CV-HS3 4-line ESD protection array displays a capacitance of 1.20 pF at a working voltage of 5 V. The 1.60 mm × 1.60 mm × 0.75 mm LLP75-packaged component demonstrates maximum leakage current of <0.10 µA, typical breakthrough voltage of 7 V at 1 mA, and maximum clamping voltage of 22 V at

TOPICS:

Pages

X
You may login with either your assigned username or your e-mail address.
The password field is case sensitive.
Loading