Advertisement
Product Releases
Subscribe to ECN Magazine Product Releases

Switches Enable PCIe 2.0 Switching While Offering Zero Delay

April 7, 2008 11:26 am | Comments

Enabling switching PCIe 2.0 data rates at 5.0Gbps and operating at 1.8V, 2.5V, or 3.3V, the MAX4888A and MAX4889A dual, passive PCIe switches allow multiple PCIe graphics cards to be used in PCs and servers. The MAX4888A (dual single-pole/double-throw- 2 × SPDT) is suited for switching two Rx or Tx equivalent lanes while the MAX4889A quad switch offers twice the capacity, handling four equivalent lanes of PCIe data with the equivalent half lanes used as one source and two destinations or two sources and one destination to minimize the effects of crosstalk. Both feature a single digital-control input (SEL) to switch signal paths designed to minimize power and skew and offer a zero delay switch. Specifications include operation from a single +3.0V to +3.6V power supply and down to +1.65V over the extended -40°C to +85°C temperature range.

One-Watt Amber and Red SMT LEDs Yield up to 42 Lumens

April 7, 2008 7:45 am | Comments

Encapsulated in a heat- and UV-resistant silicone compound, Avago’s one-Watt ASMT-MA00 amber and ASMT-MR00 red LEDs accept a drive current as high as 350mA to deliver an output of up to 42lm. Suitable for architectural and decorative lighting applications, the 3.3-mm high RoHS-compliant devices include features such as a 120° viewing angle, an exposed pad for increased heat transfer, and an ESD withstand of greater than

Computer-on Module Targets Handheld and Mobile Equipment

April 7, 2008 6:56 am | Comments

Based on the high-performance IntelR Atom processor Z500 series, the RadiSys Procelerant Z500 addresses handheld and mobile applications with features such as 1GB memory, a MicroSD socket, and an extended input voltage range for battery power. Compatible with the Type 2 COM Express pin-out, the 85 mm × 70 mm module can pair with the RadiSys heatspreader/mechanical adapter to provide drop-in replacement for existing Basic Form Factor designs.

Advertisement

Contactors Enable a Single-Capacitor 100-kvar PFC Circuit

April 7, 2008 6:53 am | Comments

With the precharging resistors for damping inrush currents integrated in the housing, the B44066S*J230/N230 Series of EPCOS capacitor contractors can create a 100-kvar circuit with a single device for PFC systems with and without reactors. The contactors extend the service life of the capacitor and PFC system via optimized switching behaviour, and are also equipped with an auxiliary contact. Available from stock at a cost of $290 each.

Fiber Optic Connector Meets Lucent and Telcordia Requirements

April 7, 2008 6:21 am | Comments

The Cannon PHD SuperLC connector from ITT Interconnect Solutions meets or exceeds Lucent 640-252-053 and Telcordia GR-326 requirements, making it suitable for military/aerospace, telecom service, and industrial data communications applications. The connector features a tunable optical cartridge that functions as a standalone optical element separate from the connector housing

FETs Reduce the Size of Wireless Devices

April 7, 2008 5:39 am | Comments

Measuring 1.0 mm × 0.5 mm × 0.25 mm, Avago Technologies’ VMMK-1218 and -1225 field effect transistors (FETs) occupy less than 5 percent the volume of a standard SOT-343 package. The VMMK-1225 supports 0.5 GHz to 26.5 GHz frequency ranges with a noise figure of less than 0.95 dB and 12 dB available gain under 50 ohms conditions at 12 GHz. The FET also offers 23 dBm output third-order intercept and 8 dBm output power.

Multipoint PICMG Card Connectors Handle up to 18A Per Contact

April 7, 2008 4:42 am | Comments

Provided in a 6-pin model as well as 5-pin and 7-pin versions compliant with PICMG EXP.0 CompactPCI Express, the Universal Power Module family of multipoint connectors from ERNI Electronics have a current carrying capacity of 18A per contact at 20°C. Hot-swap capable, the pressfit angled male devices can supply power to daughter cards in conjunction with 2 mm ERmet connectors

FVDT Filters Offer High Extenuations In 150 kHZ to 30 MHz Frequencies

April 4, 2008 8:13 am | Comments

Premo EMC's EMI FVDT filters are intended for frequency investors destined to wind turbine generator. These filters present high extenuations in 150 kHz up to 30 MHz frequencies according to EMC 2004/108/CE Directive and specific norm product EN61800-3:2004. The product range destined to wind turbine generator include

Advertisement

PoE Midspan Drives Both Low- and High-Power Peripherals

April 4, 2008 8:06 am | Comments

Able to power remote wireless LAN access points, VoIP phones, video cameras, RFID readers, and other IP terminals over the existing network cable infrastructure, GlobTek's GT-91093-HPOE Series Power over Ethernet (PoE) Midspans can be configured to 15.4W of power per port over two pairs in compliance with IEEE 802.3af standard or to 38.5W over four pairs of the CAT5e cable.

Miniaturized Ceramic Antennas Offer Flexible Placement In GPS, Bluetooth Devices

April 4, 2008 7:58 am | Comments

Ethertronics introduced two miniaturized ceramic antennas: a GPS/Bluetooth version and a GPS antenna, which is said to provide high efficiency while minimizing ground clearance and component “keep out” areas. Designed to address the challenges associated with incorporating multiple RF-functions into mobile devices, both antennas include

AWGs Furnish Complex Waveforms

April 4, 2008 7:47 am | Keysight Technologies | Comments

Using 15-bit vertical resolution, Agilent Technologies’ N6030A (PXI) and N8241A (LXI) PXI-and LXI-based arbitrary waveform generators (AWGs) can create simultaneous wide-bandwidth and high-resolution signals for electronic testing of radar, satellite, telecom or military communication equipment. Offers a spurious-free dynamic range of less than -65 dBc per channel, DC to 500 MHz, with a noise floor of less than -150 dBc/Hz. When combined with the Agilent PSG vector signal generator wideband I/Q upconverter, the AWGs can achieve modulation bandwidths as high as 1 GHz at up to 44 GHz for IF and RF subsystem testing. Each of the four-slot generators’ two channels offer 1.25 GS/s with a signal bandwidth of up to 500 MHz and a standard waveform length of 8 MS per channel, expandable to 16 MS.

Wideband DAC Provides Low-Power Performance

April 4, 2008 7:39 am | Comments

Optimized for direct digital synthesis of high-frequency and wideband signals in the first Nyquist zone, the 12-bit, 4.0Gsps MAX19693 wideband DAC from Maxim Integrated Products can synthesize signals in the frequency range from DC to nearly 2GHz. Suitable for applications such as wideband communications, radar waveform and digital signal synthesis, the 11mm2 CSBGA device offers an SFDR of greater than 70dBc below 800MHz, and 62dBc at 1500MHz with a wideband-noise spectral density of -164dBm/Hz.

Infrared SMT LEDs Promise Extended Operation

April 4, 2008 7:15 am | Comments

Housed in a plastic leadless PLCC-2 package with a silicon encapsulant, the OP180 Series and OP280 Series of SMT infrared LEDs from Optek have an increased operational life over unencapsulated emitters. The devices are available in GaAs and GaAIAs versions providing 850 nm, 875 nm, or 940 nm light at power levels from 0.15 mW/cm² to 0.15 mW/cm² of apertured power

Advertisement

Radio Communication Analyzers Test High Data Rate

April 4, 2008 6:45 am | Comments

Anritsu Company introduced its HSDPA high data rate and W-CDMA Band XI test options for its MT8820B/MT8815B radio communication analyzers to create single-instrument systems for testing next-generation high data rates and Tx/Rx characteristics. Advantages include faster measuring times, one-touch operation, high-level signaling and high performance for designers and manufacturers of HSPDA and W-CDMA mobile devices who need to quickly verify performance.

Data Logger Features a Flexible Probe

April 4, 2008 6:41 am | Comments

Omega Engineering, Inc. announced its Model OM-CP-HITEMP-150FP small, rugged, reusable temperature data logger for deployment in harsh environments. This data logger comes standard with a flexible silicone rubber cable, penetration style stainless steel probe and a stainless steel body. It features a programmable start time, real time operation and an extended temperature range. Data analysis is easy by using the accompanying Windows software, and NIST Calibration certificates are available.

TOPICS:

Pages

X
You may login with either your assigned username or your e-mail address.
The password field is case sensitive.
Loading