Based on the high-performance IntelR Atom processor Z500 series, the RadiSys Procelerant Z500 addresses handheld and mobile applications with features such as 1GB memory, a MicroSD socket, and an extended input voltage range for battery power. Compatible with the Type 2 COM Express pin-out, the 85 mm × 70 mm module can pair with the RadiSys heatspreader/mechanical adapter to provide drop-in replacement for existing Basic Form Factor designs.
With the precharging resistors for damping inrush currents integrated in the housing, the B44066S*J230/N230 Series of EPCOS capacitor contractors can create a 100-kvar circuit with a single device for PFC systems with and without reactors. The contactors extend the service life of the capacitor and PFC system via optimized switching behaviour, and are also equipped with an auxiliary contact. Available from stock at a cost of $290 each.
The Cannon PHD SuperLC connector from ITT Interconnect Solutions meets or exceeds Lucent 640-252-053 and Telcordia GR-326 requirements, making it suitable for military/aerospace, telecom service, and industrial data communications applications. The connector features a tunable optical cartridge that functions as a standalone optical element separate from the connector housing
Measuring 1.0 mm × 0.5 mm × 0.25 mm, Avago Technologies’ VMMK-1218 and -1225 field effect transistors (FETs) occupy less than 5 percent the volume of a standard SOT-343 package. The VMMK-1225 supports 0.5 GHz to 26.5 GHz frequency ranges with a noise figure of less than 0.95 dB and 12 dB available gain under 50 ohms conditions at 12 GHz. The FET also offers 23 dBm output third-order intercept and 8 dBm output power.
Provided in a 6-pin model as well as 5-pin and 7-pin versions compliant with PICMG EXP.0 CompactPCI Express, the Universal Power Module family of multipoint connectors from ERNI Electronics have a current carrying capacity of 18A per contact at 20°C. Hot-swap capable, the pressfit angled male devices can supply power to daughter cards in conjunction with 2 mm ERmet connectors
Premo EMC's EMI FVDT filters are intended for frequency investors destined to wind turbine generator. These filters present high extenuations in 150 kHz up to 30 MHz frequencies according to EMC 2004/108/CE Directive and specific norm product EN61800-3:2004. The product range destined to wind turbine generator include
Able to power remote wireless LAN access points, VoIP phones, video cameras, RFID readers, and other IP terminals over the existing network cable infrastructure, GlobTek's GT-91093-HPOE Series Power over Ethernet (PoE) Midspans can be configured to 15.4W of power per port over two pairs in compliance with IEEE 802.3af standard or to 38.5W over four pairs of the CAT5e cable.
Ethertronics introduced two miniaturized ceramic antennas: a GPS/Bluetooth version and a GPS antenna, which is said to provide high efficiency while minimizing ground clearance and component “keep out” areas. Designed to address the challenges associated with incorporating multiple RF-functions into mobile devices, both antennas include
Using 15-bit vertical resolution, Agilent Technologies’ N6030A (PXI) and N8241A (LXI) PXI-and LXI-based arbitrary waveform generators (AWGs) can create simultaneous wide-bandwidth and high-resolution signals for electronic testing of radar, satellite, telecom or military communication equipment. Offers a spurious-free dynamic range of less than -65 dBc per channel, DC to 500 MHz, with a noise floor of less than -150 dBc/Hz. When combined with the Agilent PSG vector signal generator wideband I/Q upconverter, the AWGs can achieve modulation bandwidths as high as 1 GHz at up to 44 GHz for IF and RF subsystem testing. Each of the four-slot generators’ two channels offer 1.25 GS/s with a signal bandwidth of up to 500 MHz and a standard waveform length of 8 MS per channel, expandable to 16 MS.
Optimized for direct digital synthesis of high-frequency and wideband signals in the first Nyquist zone, the 12-bit, 4.0Gsps MAX19693 wideband DAC from Maxim Integrated Products can synthesize signals in the frequency range from DC to nearly 2GHz. Suitable for applications such as wideband communications, radar waveform and digital signal synthesis, the 11mm2 CSBGA device offers an SFDR of greater than 70dBc below 800MHz, and 62dBc at 1500MHz with a wideband-noise spectral density of -164dBm/Hz.
Housed in a plastic leadless PLCC-2 package with a silicon encapsulant, the OP180 Series and OP280 Series of SMT infrared LEDs from Optek have an increased operational life over unencapsulated emitters. The devices are available in GaAs and GaAIAs versions providing 850 nm, 875 nm, or 940 nm light at power levels from 0.15 mW/cm² to 0.15 mW/cm² of apertured power
Anritsu Company introduced its HSDPA high data rate and W-CDMA Band XI test options for its MT8820B/MT8815B radio communication analyzers to create single-instrument systems for testing next-generation high data rates and Tx/Rx characteristics. Advantages include faster measuring times, one-touch operation, high-level signaling and high performance for designers and manufacturers of HSPDA and W-CDMA mobile devices who need to quickly verify performance.
Omega Engineering, Inc. announced its Model OM-CP-HITEMP-150FP small, rugged, reusable temperature data logger for deployment in harsh environments. This data logger comes standard with a flexible silicone rubber cable, penetration style stainless steel probe and a stainless steel body. It features a programmable start time, real time operation and an extended temperature range. Data analysis is easy by using the accompanying Windows software, and NIST Calibration certificates are available.
Boonton, a Wireless Telecom Group company, introduced its PIM 20 ultra portable test system for passive intermodulation. Its design provides a rugged, reliable tool for RF field technicians. The device is battery-driven and self-calibrating. When connected to a component or system, users can read the measurement value (dBc) directly from the display, follow the LED bar that turns red if too high of a PIM value is measured, or they can connect it to a device like a Walkie-Talkie to listen remotely if PIM values change when altering components (e.g. tap test).
Using optional barriers that prevent color mixing from adjacent rows Elma Electronics’ LED Lightpipes provide distinct color output. The lightpipes have thin polycarbonate barriers which are configurable, block intruding light from other tube lanes, and add strength; resulting in clear, segregated color definition. The lightpipes offer the flexibility to have barriers between some or all of pipes, allowing the ability to mix and match.