Based on the 400,000-gate and 8,000-logic-cell 3S400A FPGA from Xilinx, a development kit from Avnet provides a platform for experimenting and prototyping applications based on the Xilinx Spartan-3A FPGA family. Suitable for exploring general logic designs as well as DSP and MicroBlaze-based embedded processing applications
Targeting amplifiers, discrete transistors, and diodes where more than 0.5W is consumed, StratEdge's new family of small outline thermally enhanced molded ceramic packages for power semiconductors can be used for silicon, silicon carbide, gallium nitride, and other compound semiconductors in power applications.
The STC5270 from Connor-Winfield is an integrated single chip solution for the synchronous clock in SDH, SONET, and synchronous Ethernet network elements. The device is fully compliant with ITU-G.813 and Telcordia GR1244 and GR253. The STC5270 accepts 2 reference inputs and generates 2 independent synchronized output clocks. Reference input frequencies are automatically detected. All reference switches are hitless.
Providing USB 2.0 on-the-go (OTG) functionality to enabled devices, the PIC32MX420F032H-40I/PT USB On-The-Go PIC32 Microcontroller from Microchip provides designers with the flexibility to add all three modes of USB operation to their products. USB OTB functionality also includes the ability to auto-negotiate
Designed for side- and top-actuation with a board height of 3.5 mm, the HDT Series detect switch is suitable for use in Advanced Mezzanine Card (AMC) applications. Features include an operational life of 100,000 cycles with a maximum actuation force of 35 gm, a pre-travel of 0.30 mm, and an over-travel of 0.75 mm.
Streamlining the digital communication between high speed ADCs and FPGAs, the Linear Technology LTC2274 16-bit, 105Msps ADC reduces the number of data I/O lines required between the ADC and the FPGA from 16 CMOS or 32 LVDS parallel data lines to a single, self-clocking, differential pair communicating at 2.1Gbps. Consuming 1.3W from a 3.3V analog supply, the 6mm² QFN-40-packaged device includes
Beta Transformer Technology Corporation introduced the MLP-2205 compact 0.4” × 0.4” footprint, 0.185” maximum height single channel transformer. A pair of MLP-2205 transformers can be used for dual channel applications yielding an overall footprint that is smaller than industry-available dual transformers.
Available in standard case sizes 0402 through 3838 State of the Art has expanded its line of high frequency chip resistors. The devices are optimized for 50 ohm characteristic impedance using special manufacturing techniques to reduce VSWR. Power ratings for the resistors range from 50 mW up to 200W and a low return loss, up to 20 GHz.
Bomar’s shielded connector, the EZ-RJ45, exceeds the CAT 6 performance requirements per TIA/EIA-568-B when used in conjunction with a standard strain relief boot, or the new snagless boot. It is therefore suitable for a wide range of high-speed residential, telecommunications, and broadband communications applications where
The HTWAT series of silicone rubber heating tapes from Omega Engineering feature an adjustable thermostat control up to 218°C (425°F) and are designed for process temperature control, freeze protection, and supplemental heat. The heating tapes are moisture and chemical resistant, suitable for electrically conductive surfaces, and heat up at a very quick rate. Recommended applications include valves, pipe lines, bearings, filter housings
Created by the Small Form Factor Special Interest Group (SFF-SIG), a collaboration of board, I/O suppliers, and component manufacturers led by WinSystems, VIA Technologies, VersaLogic, Octagon, and Ampro, the SUMIT interface specification is intended to improve I/O issues in next generation SBCs.
With voltage ratings from 750V to 20,000V and a resistance range from 330kO to 1GO, IRC's CMH Series of thick film resistors are qualified to MIL-PRF-49462. Suitable for high reliability applications including military communications, radar equipment, high-voltage power supplies and medical electronics
QSW (Quick Shrink Wrap) heat-shrinkable wraparound repair sleeves from Tyco Electronics are available in flat sheets with widths of 60 or 100 mm and lengths of 100 mm, 200 mm, 300 mm and 400 mm. The black, adhesive-backed polyolefin wraparound sleeves permit fast, permanent repairs of minor damage to cable insulation without requiring the connector to be removed from the cable prior to repair.
Presented as the semiconductor industry’s first F-RAM-based Event Data Recorder (EDR) the FM6124 from Ramtron International continuously monitors state changes, stores them in the F-RAM, and alerts the system to the changes. Like a programmable logic controller (PLC), the device features simple device settings and data retrieval for easy system integration and a shorter design-in cycle. The device is designed for use
PCB Piezotronics introduced Model 478A30, a three-channel DC sensor signal conditioner with selectable gain. This model is designed to be compatible with new Series 3991/3993 high amplitude 20,000g MEMS DC response shock accelerometers, and providing the end user with