Advertisement

Integrated C-V Module

October 9, 2007 5:05 am | Keithley Instruments | Product Releases | Comments

Keithley Instruments, Inc. announces a C-V measurement instrument for its Model 4200-SCS Semiconductor Characterization System. The Model 4200-CVU instrument comes as a module that plugs into any available instrument slot of the Model 4200-SCS, allowing fast and easy capacitance measurements from femtoFarads (fF) to nanoFarads (nF), at frequencies from 10 kHz to 10 MHz.

LISTED UNDER: Test & Measurement
Advertisement

Frequency Standard Features 20 MHz Synthesizer

October 2, 2007 11:24 am | Product Releases | Comments

Novatech Instruments, Inc. introduced the Model 2975AX Disciplined Quartz Frequency Standard. This bench-top instrument provides a cost-effective means to generate precise frequency reference signals for laboratory instruments, communication systems or other test and measurement equipment. Containing an ovenized quartz crystal time-base, the device has a stability of ±5 × 10-11 per day when disciplined to a 1 pps source

LISTED UNDER: Test & Measurement

Serial Analyzers for PCIe 2.0 Provide Power Management and Cross Bus Analysis

September 26, 2007 7:06 am | Tektronix | Product Releases | Comments

Tektronix announced new TLA7S16 and TLA7S08 Serial Analyzers for test and validation of PCI Express (PCIe) 1.0 and 2.0 designs. The devices provide detailed PCIe 2.0 protocol information along with cross-bus analysis. The new analyzers plug into the company’s TLA7000 Series logic analyzers, adding the ability to debug and correlate general purpose signals and other system interconnects including memory and computer processors.

LISTED UNDER: Test & Measurement

Test Options for 3G Radio Communications Analyzers

September 25, 2007 8:13 am | Product Releases | Comments

Anritsu Company introduces three options for its MT8820B/MT8815B radio communication analyzers that allow for fast and efficient testing of TD-SCDMA 3G mobile terminals. The MT8820B-007/MT8815B-007 TD-SCDMA measurement hardware, MX882007C TD-SCDMA measurement software and the MX882007C-001 TD-SCDMA voice codec options complement the inherent testing advantages of the analyzers to provide manufacturers with an efficient test tool for conducting call-processing, RF Rx/Tx and voice tests of TD-SCDMA mobile terminals.

LISTED UNDER: Test & Measurement

Analog/Mixed-Signal Test System

September 25, 2007 8:10 am | Product Releases | Comments

FETtest announces its AMX400, a modular, high-performance system for production analog/mixed-signal test applications. It offers a variety of instrumentation options, software for enterprise-wide test environments and support for avariety of devices. From wafer sort to final test, the system supports parallel testing of up to 32 multi-sites with 96 pin analog/digital stimulus/measure, software for test development and production test management and execution.

LISTED UNDER: Test & Measurement

Quartz Frequency Standard Features 1 pps Tracking

September 25, 2007 8:08 am | Product Releases | Comments

Novatech Instruments, Inc. introduces its Model 2960AX disciplined quartz frequency standard. This bench-top instrument provides a way to generate precise frequency reference signals for laboratory equipment and communication systems. Containing an ovenized quartz crystal time-base, it has a stability of better than ±5 × 10-11 per day when disciplined to a 1 pps source.

LISTED UNDER: Test & Measurement

Four-Channel Jitter Tolerance Test Systems

September 25, 2007 8:04 am | Product Releases | Comments

Anritsu Company introduces its MU181000B 12.5 GHz four-port synthesizer, the MU181000A/B-001 jitter modulation option and the MX180005A jitter application software for its MP1800A signal quality analyzer series. These options allow the series to conduct accurate jitter tolerance measurements on devices with up to four channels such as multi-channel CPU boards, PC boards and optical devices, forming interconnects in routers, servers and super computers.

LISTED UNDER: Test & Measurement

Ultrasonic Rangefinders Feature Custom Beam Width

September 25, 2007 7:40 am | Product Releases | Comments

MaxBotix, Inc. announces its LV-MaxSonar sensor with a factory calibrated beam width, allowing precision beam angles. Five ultrasonic rangefinders in the line are calibrated to a specific beam width, allowing users to select the sensor that provides the beam width of choice. The sensor beam width is widest for the model EZ0 that is well suited for users needing a high sensitivity or a wide beam width. Each sensor, the EZ1, EZ2, EZ3 and EZ4, is progressively narrower.

LISTED UNDER: Test & Measurement

Micro-Ohmmeter Low Resistance Tester

September 25, 2007 7:36 am | Product Releases | Comments

The Palmer Wahl Instrumentation Group introduces its Wahl RM116 micro-ohmmeter that is a low resistance tester for harsh conditions in maintenance departments, workshops and field use, performing measurements on inductive and non-inductive resistances with a DC current. Its large interactive display informs the operator in real time about the type of measurement, range, calculation conditions (resistance calculated according to a reference temperature), thresholds status and values.

LISTED UNDER: Test & Measurement

Signal Detection Products for Industrial Fields

September 25, 2007 7:29 am | Product Releases | Comments

MADE announces its SkyRadio for overhead high-voltage line detection on construction sites and the Nadir system for pre-identifying live low-voltage cables and feeders for electrical utility work. The SkyRadio system helps detect high-voltage electrical lines overhead. It includes one-to-eight wireless sensors on the high point of the equipment and corresponding transmitter/receiver modules that communicate with the central processing unit. The Nadir system has two components to identify live low-voltage cables under load in a trench or substation exit.

LISTED UNDER: Test & Measurement

Pressure Transmitter for Drilling and Well Applications

September 25, 2007 7:22 am | Product Releases | Comments

Automation Products Group, Inc. introduces its Hammer Union pressure transmitter that is used with highly abrasive and corrosive media. It provides long life in harsh oil patch environments in applications such as mud logging, cementing, fracturing and acidizing. With CSA certification for safe operation in hazardous locations, the NEMA 4X/IP44 transmitter also complies with new NACE MR01-75 standards for sour gas pressure applications.

LISTED UNDER: Test & Measurement

Calibrator Kit Increases Wireless Test Precision

September 25, 2007 7:04 am | Product Releases | Comments

LitePoint Corp. announces its TrueCableT kit that measures the loss of cables used in precision wireless test set-ups such as channel emulation. The calibrator allows chipset vendors, OEMs and quality-approval groups to achieve optimum test accuracy in a straight-forward manner. The instrument consists of an RF unit that is attached to an IQview or IQflex one-box tester VSG port.

LISTED UNDER: Test & Measurement

Embedded Data Acquisition and Strain Gauge Interface Board

September 25, 2007 6:57 am | Product Releases | Comments

Electro Standards Laboratories announces its model 4333 CellMite ProD high performance embedded data acquisition and strain gauge interface board that is suitable for embedded applications that require high speed analog and digital data acquisition. The board features dual 24-bit independent strain gauge channels with simultaneous sampling at 15,000 samples/second that can also be configured as quad 24-bit strain gauge channels sampled at 5,000 samples/second.

LISTED UNDER: Test & Measurement

Test, Measurement and Control Products

September 25, 2007 6:53 am | Product Releases | Comments

Microstar Laboratories announces its DAPserver 400 and its DAPserver 400R test, measurement and control products that combine a five-slot PCI backplane and a 10-slot Eurocard cage in an industrial-grade chassis. A Pentium M processor runs server software on a board that occupies one of the PCI slots. This software and the software running on DAP boards protects applications from local or network-related delays.

LISTED UNDER: Test & Measurement

Multi-Function DMM

September 25, 2007 6:42 am | Product Releases | Comments

Protek Test and Measurement introduces its model 6300 category III 600V five-in-one, multi-function, 4,000 count, DMM and also its model 6100. The 6300 has built-in light level, sound level, relative humidity and temperature capabilities in addition to DMM functions. The 6300 and 6100 are auto-ranging 4,000 count DMMs with 3-3/4¨ digit displays. In addition to measuring AC/DC voltages from 100 µV to 1,000V, AC/DC current from 400 µA to 10A, and resistance from 0.1? to 40 Meg?

LISTED UNDER: Test & Measurement

Pages

X
You may login with either your assigned username or your e-mail address.
The password field is case sensitive.
Loading