Advertisement
Probes

CableEye® M3U Cable Tester System: Item 821U

March 3, 2015 5:00 pm | CAMI Research, Inc. | Products

For diagnostic and Pass/Fail Testing — Find, display, log, document: opens, shorts, miswires, intermittent connections, continuity, contact and isolation resistance, embedded resistors and diodes. • 152 Test point base unit (for ≤76-conductor cable) • Expandable to 2560 test points (for >76-conductor cable) • Resistance measurement 0.3Ω-10MΩ • Graphical User Interface (GUI) • 9x12" bench footprint
 ◊ Includes: CB15 board set (Item 745), PC s/w, DB of >200 standard cables, 1yr warranty, 1yr free tech support, one-year free software and database upgrades. USB interface standard. ◊ If cables will never exceed 64 conductors, the M2-Basic system (Item 810) offers similar capabilities without resistance measurement at a lower cost.

LISTED UNDER: Schematic Capture | Data Acquisition | Data Loggers

CableEye® HVX HiPot Cable Tester System: Base Unit Item 829

March 3, 2015 4:48 pm | CAMI Research, Inc. | Products

For diagnostic and Pass/Fail Testing — Permits expanded testing for insulation resistance and dielectric breakdown. After checking for opens, shorts, miswires, and resistance limits, the HVX hipot module will apply a user-selectable voltage from 10v to 1500v DC, or 10v to 1000v RMS AC, to each connection group in the cable. Ramp Up, Ramp Down, Dwell Time (same as Test Time), Trip Current, and Trip Delay (same as Soak Time) may be programmed for your specific requirements. Current leakage detected during the high voltage test phase provides a measure of insulation resistance up to 1 GΩ, and any leakage current exceeding a preset limit reveals the presence of moisture, flux, or other contamination on exposed contacts.

LISTED UNDER: Data Loggers | Meters | Probes

EMC probe kit suitable for detecting radiated emissions

February 20, 2015 2:18 pm | by Saelig Company, Inc. | Saelig Company, Inc. | Product Releases | Comments

The economical TBPS01-TBWA2 EMC Probe Kit consists of four rubber-handled near-field probes (three H-field and one E-field), a 20dB or a 40dB wideband amplifier, and associated cables, supplied in an attractive wooden case. The shielded probes have built-in ferrites and insulated ...

LISTED UNDER: Receivers | Active
Advertisement

Control software offers high gains in speed and productivity

February 2, 2015 3:36 pm | by Cascade Microtech | Cascade Microtech | Product Releases | Comments

Cascade Microtech has evolved its probe station user environment to an unprecedented level of power and efficiency with the latest release of Velox. The company has consolidated its Nucleus and ProberBench system software packages into a universal ...

LISTED UNDER: Test Instrumentation | High Frequency | RF/Microwave

EMC probe set detect EMI emissions up to 12GHz

October 29, 2014 5:38 pm | Saelig Company, Inc. | Product Releases | Comments

Saelig Company, Inc. (Fairport, NY) announces the availability of the TNP6Gx Near-Field EMI Probe Set - ideal for investigating interference sources, estimating interference field strengths, verifying shielding and filtering designs, identifying faulty components ...

LISTED UNDER: Test & Measurement | Probes | RF/Microwave

USB pen scope displays signals from 5mV to 50V

August 21, 2014 4:27 pm | Saelig Company, Inc. | Product Releases | Comments

Saelig Company Inc. (Fairport, NY) announces the new Owon RDS1021 Wave Rambler — a new, USB pen scope that packs the features of a high-performance bench top oscilloscope in a small, lightweight and ergonomic probe that fits perfectly in the hand....

LISTED UNDER: Test & Measurement | Probes | Oscilloscope

Test probe cable assemblies designed for the inspection of high-frequency circuits

August 11, 2014 9:31 am | Product Releases | Comments

GradConn (Boca Raton, FL) has launched a new range of low-cost co-axial test probe cable assemblies for the inspection of high frequency circuits. Suitable for testing Hirose MS-156 and Murata MM8030 sub miniature coaxial switch connectors ...

LISTED UNDER: Test & Measurement | Probes | Test

6GHz handheld RF spectrum analyzers provide more than 3 hours of operation

August 5, 2014 12:34 pm | Saelig Company, Inc. | Product Releases | Comments

Saelig Company, Inc. (Fairport, NY) has introduced two new RF analyzers — the new AIM-TTi Series 5 Models — available in 3.6GHz and 6.0GHz versions. They maintain a true handheld format while offering bench-top instrument-quality features....

LISTED UNDER: Test & Measurement | RF/Microwave
Advertisement

Oscilloscopes reduce test time in research, development, and failure-analysis applications

June 27, 2014 12:13 pm | Saelig Company, Inc. | Product Releases | Comments

Saelig Company, Inc. (Fairport, NY) has announced the availability of MSO functionality to their range of Rigol DS2000A and DS1000Z scopes. The mixed-signal extension provides digital signal debug capabilities to the user, allowing simultaneous viewing of analog and digital signals for comprehensive signal analysis....

LISTED UNDER: Oscilloscope

2014 IMPACT Award Winner: Signal Hound wins for Test and Measurement

May 27, 2014 3:35 pm | Product Releases | Comments

The BB60A Real-Time Spectrum Analyzer / RF Recorder from Signal Hound (La Center, WA) is powered and controlled solely over USB 3.0 link and a PC with an Intel Core i7 processor. The BB60A circumvents the traditional need for a processor, display, keyboard, and power supply by using a PC....

LISTED UNDER: RF/Microwave

Socket probe adapter designed to interface with 0.5mm pitch Fine pitch Ball Grid Array packages

April 30, 2014 3:23 pm | Ironwood Electronics, Inc. | Product Releases | Comments

Ironwood Electronics' (Eagan, MN) PB-BGA133A-Z-01 Socket Probe Adapter which allows high-speed testing of BGA device while accessing the signals using testers via header pins. Features of the PB-BGA133A-Z-01 include shortest possible trace length for maximum speed....

LISTED UNDER: Test

Anti-diffusion gold coating lessens or eliminates the need for probe cleaning

March 10, 2014 3:18 pm | Product Releases | Comments

Aries Electronics (Bristol, PA) announced the introduction of its unique Protect-A Probe, anti-diffusion, gold coating for its complete line of burn-in and test socket spring probes. The Protect-A Probe coating is designed to lessen or eliminate the need for probe cleaning....

LISTED UNDER: Test

Miniature infrared touch probe designed for micro-machining applications

February 25, 2014 3:32 pm | Product Releases | Comments

Hexagon Metrology (North Kingstown, RI) announced the availability of the m&h IRP40.50 infrared touch probe for the North American market. The IRP40.50 is ideal for inspection in tight spaces and was designed to address the needs of miniature machining centers.

LISTED UNDER: Active

RF power detectors feature wide dynamic range and best-in-class accuracy

December 16, 2013 2:49 pm | Analog Devices, Inc. | Product Releases | Comments

Analog Devices introduced two RF power detectors with wide dynamic range and best-in-class accuracy and temperature stability. Designed with ADI’s leading detector expertise, the ADL5903 RF detector is an optimal solution for a variety of high-frequency systems....

LISTED UNDER: High Frequency

Handheld current probes include highest frequency range available on the market

November 21, 2013 10:23 am | Product Releases | Comments

Cal Test Electronics today introduced the new CP6000 Series, a four-model family of ELDITEST AC/DC oscilloscope clamp on current probes with the highest frequency range available on the market. Along with the current probes, kits include an insulated BNC cable assembly for scope connection, BNC to banana plug adapter, selected region power adapter and user manual.

LISTED UNDER: Oscilloscope

Pages

X
You may login with either your assigned username or your e-mail address.
The password field is case sensitive.
Loading