Advertisement
Digital

Digitizers boast real-time sampling rates up to 5 GS/s

February 23, 2015 10:14 am | by Spectrum Instrumentation Corp. | Spectrum Instrumentation Corp. | Product Releases | Comments

For the first time Spectrum is offering a solution to engineers and scientists looking to capture and analyze fast electronic signals in the DC to 1.5 GHz frequency range. The company has greatly extended the performance of its PCIe based instruments by adding nine new models to its M4i series of digitizers. These cards boast real-time sampling rates up to 5 GS/s and high bandwidth making it...

LISTED UNDER: ICs | Digital

Digital signal controllers provide 5V operation

November 25, 2014 3:34 pm | Microchip Technology Inc. | Product Releases | Comments

Microchip Technology Inc. (Chandler, AZ) announced from the SPS IPC Drives Conference in Germany a new family of 16-bit dsPIC33 Digital Signal Controllers (DSCs) with the dsPIC33 "EV" family. This new family provides 5V operation for improved ...

LISTED UNDER: ICs | Digital

IC linearizes temperature sensors with good accuracy

November 24, 2014 1:01 pm | Linear Technology Corporation | Product Releases | Comments

Linear Technology Corporation (Milpitas, CA) introduces the LTC2983 high-performance digital temperature measurement IC which directly digitizes RTDs, thermocouples, thermistors, and external diodes with 0.1°C accuracy and good resolution....

LISTED UNDER: ICs | Digital
Advertisement

Dual-wideband transceiver includes frequency range of 70 MHz to 6 GHz

November 17, 2014 1:13 pm | Vadatech, Inc. | Product Releases | Comments

VadaTech (Henderson, NV) has announced a dual-wideband transceiver in the FPGA Mezzanine Card (FMC) format. The board has a frequency range of 70 MHz to 6 GHz. The FMC214 utilizes eight SSMC connectors for the input/output. It combines ...

LISTED UNDER: ICs | Digital | CAN Bus Driver/Receiver

Discrete-to-digital sensor features internal lightning protection

October 22, 2014 1:47 pm | Holt Integrated Circuits | Product Releases | Comments

Holt Integrated Circuits (Mission Viejo, CA) announced a new discrete-to-digital sensor IC, HI-8429, an 8-channel device with programmable sense channels and internal lightning protection. The sense input thresholds are programmable....

LISTED UNDER: ICs | Digital

VCO operates at 1680 MHz

August 28, 2014 3:03 pm | Product Releases | Comments

Crystek’s (Fort Myers, FL) CVCO55CC-1680-1680 VCO (Voltage Controlled Oscillator) operates at 1680 MHz with a control voltage range of 0.5 V to 4.5 V. This VCO features a typical phase noise of -117 dBc/Hz at 10 kHz offset and has desirable linearity....

LISTED UNDER: Digital | Oscillators/Dividers | RF & Microwave/Communications

Receiver operates without MCU

November 11, 2013 8:44 am | Holt Integrated Circuits | Product Releases | Comments

Holt Integrated Circuits announced the introduction of HI-8475, a novel ARINC 429 receiver designed specifically for use without a microprocessor. All configuration and control is programmed using logic input pins, eliminating the need for a microprocessor or software interface and the related costs for software certification.

LISTED UNDER: CAN Bus Driver/Receiver

Digital step attenuator operates from 9 kHz to 8 GHz

October 9, 2013 5:36 pm | Richardson RFPD, Inc. | Product Releases | Comments

Richardson RFPD, Inc. today announces immediate availability and full design support capabilities for a new high frequency, high power, 7-bit digital step attenuator (DSA) from Peregrine Semiconductor Corporation (Peregrine). The PE43704 operates from 9 kHz to 8 GHz....

LISTED UNDER: Oscillators/Dividers
Advertisement

High-speed CAN transceivers are low power and highly robust

June 25, 2013 10:17 am | Microchip Technology Inc. | Product Releases | Comments

Microchip Technology Inc. announced a family of High-Speed (HS) CAN transceivers, the MCP2561/2. These new devices serve as an interface between a CAN protocol controller and the physical two-wire CAN bus. The new family of transceivers meet CAN specification requirement

LISTED UNDER: CAN Bus Driver/Receiver

Innovative chip provides ultra-low voltage characteristics

May 28, 2013 9:56 am | Goepel Electronics Llc | Product Releases | Comments

GOEPEL electronic introduces CION LX, a new generation of JTAG transceiver ICs. The innovative chip provides ultra-low voltage characteristics, offering a tester-per-pin architecture based on diverse Boundary Scan standards such as IEEE 1149.1, IEEE 1149.6 and IEEE 1149.8.1, in combination with additional digital and analogue test instruments.

LISTED UNDER: Bus Drivers

25 MBd digital optocoupler device achieves 3,750 VRMS signal isolation

May 14, 2013 3:06 pm | Product Releases | Comments

Avago Technologies announced a new dual-channel bi-directional 25 MBd digital optocoupler device, the ACSL-7210. The device is a dual-channel high speed digital optocoupler optimized for bi-directional industrial communication networks using high speed protocols such as PROFIBUS fieldbus and Serial Peripheral Interface (SPI).

LISTED UNDER: Bus Drivers

Electronic Components - Active and Passive - Buy Online

April 3, 2013 4:21 pm | 1-Source Electronic Components, Inc. | Products

Semiconductors, Connectors, Capacitors - Buy online - Look up Spec and Data Sheets - www.1sinc.com

LISTED UNDER: Logic | Power Management | Sensor

Electronic Components - Active and Passive - Buy Online

April 3, 2013 4:20 pm | 1-Source Electronic Components, Inc. | Products

Semiconductors, Connectors, Capacitors - Buy online - Look up Spec and Data Sheets -

LISTED UNDER: Logic | Power Management | Sensor

BPF with LGA-type terminations has 3dB bandwidth of 100MHz centered at 2.45GHz

January 7, 2013 10:52 am | Rfmw Ltd | Product Releases | Comments

RFMW, Ltd. announces design and sales support for Johanson Technology’s (JTI) newly introduced  2.4GHz, High-Rejection Band Pass Filter (BPF) with Land Grid Array (LGA)-type terminations. This  brand new BPF has the highest close-to-passband rejection with the smallest footprint ever made by JTI.

LISTED UNDER: Filters

CAN transceivers capable of operating in temperatures from −55°C to 200°C

December 20, 2012 10:46 am | Holt Integrated Circuits | Product Releases | Comments

Holt Integrated Circuits today announced the introduction of a family of CAN transceivers capable of operating in temperatures from −55°C to 200oC. The devices are ARINC 825 / ISO 11898-5 compliant and are targeted at high temperature avionics and industrial applications such as aircraft braking systems, engine controls and down-hole drilling.

LISTED UNDER: CAN Bus Driver/Receiver
X
You may login with either your assigned username or your e-mail address.
The password field is case sensitive.
Loading