Advertisement
Articles
Subscribe to ECN Magazine Articles
View Sample

FREE Email Newsletter

ECN Daily

Connectors Meet Soldiers’ Protection, Secure Connection Requirements

April 30, 2010 7:35 am | by Elizabeth Rubbo, Fischer Connectors, www.fischerconnectors.com | Comments

Around the world, Future Soldier Programs are focused primarily on development of technologies to reduce the soldiers fighting load and power requirements, improve the soldier’s protection, lethality, and environmental and situational awareness.

TOPICS:

New FMC Standard Drives Performance in Aerospace and Defense Signal Processing Systems

April 30, 2010 7:09 am | by Jeremy Banks, Curtiss-Wright Controls Embedded Computing | Comments

New generations of FPGAs present developers with a level of processing performance and potential I/O bandwidth that cannot easily be matched by conventional CPU configurations. While many COTS solutions enable developers to readily make use of FPGAs for processing, the real challenge to an application is often measured in terms of I/O bandwidth, latency and connectivity.

TOPICS:

Comparing the Impact of Different Heat Sink Materials on Cooling Performance

April 30, 2010 7:00 am | by Michael Haskell, Thermal Engineer, Advanced Thermal Solutions, Inc., www.Qats.com | Comments

This article addresses the impact of material choice on heat sink performance. First, we evaluate different materials using mechanical samples and a research quality wind tunnel. This testing compares a constant heat sink geometry made from copper, aluminum, and graphite foam.

TOPICS:
Advertisement

Why You Should Care About Green Storage

April 30, 2010 6:16 am | by Tom McDorman, vice president and general manager of enterprise storage solutions, WD | Comments

There is a lot of talk about going “green” lately, and while it is noble, timely and responsible to save the environment from excessive green house gases, in these tough economic times, it can be equally as responsible to lower energy and power costs.

TOPICS:

Neutral stance

April 30, 2010 6:11 am | by Chris Warner, Executive Editor | Comments

As a result of the Comcast Corp. v. Federal Communications Commission (FCC) court decision, Internet service providers (ISPs) are no longer constrained from slowing or blocking different types of content or access to sites that offer content that conflicts with the providers’ interests.

TOPICS:

No More Silos Allowed for Thermal and EMI Engineers as Frequencies Rise

April 29, 2010 12:58 pm | by Jeff McCutcheon, senior technical specialist,3M Electronics Markets Materials Division | Comments

Are you a “Themimech” engineer? If not now, you might be soon! As the rising frequencies of many applications are now forcing engineers to be aware of and plan for issues related to rising frequencies in electronic devices and systems, they are now required to participate...

TOPICS:

Performing Accurate Nonlinear Device Measurements Using Active Tuners

April 29, 2010 12:04 pm | by Steve Reyes, Anritsu Company | Comments

With continued pressure for broader 3G coverage for smart phones, increased Internet connection for Wi-Fi and WiMAX, and the imminent introduction of 4G/LTE systems, design activity for digital communication RF components has never been greater.

TOPICS:

Can hypervisors Stand the Test of Real Time?

April 29, 2010 11:45 am | by Yi Zheng, QNX Software Systems | Comments

Hardware virtualization, and the hypervisors that enable it, have become a hot topic in the embedded space. But while virtualization opens up new possibilities for system architects and designers, it also poses new challenges, especially when used with real-time applications.

TOPICS:
Advertisement

Designing Custom, Low-Cost Instrumentation for Test and Measurement Using Off-the-Shelf FPGA Modules

April 29, 2010 11:36 am | by Jake Janovetz, Opal Kelly | Comments

Designing for industrial applications presents many challenges, but it also allows an engineer to be creative, spread her wings, and explore new technologies to solve the task at hand. Field-Programmable Gate Arrays (FPGAs) and, in particular, commercial off-the-shelf (COTS) FPGA modules can be just the ticket to attack industrial applications that used to be a much more difficult challenge.

TOPICS:

Smart, Intuitive User Interfaces Move to Industrial Control

April 29, 2010 11:26 am | Comments

Industrial applications, such as home and commercial building automation, data loggers, point-of-sale terminals and cash registers, in-house displays for energy metering, alarm systems and medical equipment are starting to join the “smart” revolution currently enjoyed by portable media player and smartphone markets.

TOPICS:

Vibration Analysis Using ADCs Keeps Industrial Equipment Working

April 29, 2010 10:31 am | by Michael Clifford, Analog Devices, www.analog.com | Comments

Monitoring the condition of large industrial machinery provides long term benefits in terms of lower production cost, reduced equipment down time, improved reliability, and increased safety. Industrial manufacturers face a constant battle in keeping production equipment operational.

TOPICS:

Brainstorm: Medical Electronics

April 28, 2010 8:34 am | Comments

What future technologies will reduce healthcare costs?

TOPICS:

Brainstorm: CAD-Prototyping

April 28, 2010 5:27 am | by Edited by Jason Lomberg, Technical Editor | Comments

Is breadboarding dead?

TOPICS:
Advertisement

MIMO Over-the-Air: Facing the Challenges of Testing Wireless MIMO Devices

April 22, 2010 5:08 am | by Jukka-Pekka Nuutinen, EB, Elektrobit, www.elektrobit.com | Comments

There seems to be no end to the demand of higher data rate applications and performance requirements as the number of new mobile devices continues to increase dramatically. The usage of mobile devices has evolved from voice only to multimedia messaging, downloading emails, web browsing, online gaming, video calls, social networking etc.

TOPICS:

Playing telephone

April 20, 2010 7:38 am | Comments

A pop musician recently reminded me that hit songs aren’t only catchy tunes; they are also a barometer of culture. I never expected to refer to Lady Gaga with anything other than casual references to her music or her edgy style (I’ve heard it called “21st-century Madonna), but one of her recent songs gave me some pause.

TOPICS:

Pages

X
You may login with either your assigned username or your e-mail address.
The password field is case sensitive.
Loading