Serving the Electronic Design Community Since 1956
Crimp-Style Connectors Suit Underwater Applications
November 7, 2008 5:24 am | Product Releases | CommentsDesigned for both extreme moisture and non-submersion applications, the WPJ Series wire-to-wire and wire-to-board crimp-style connectors from JST Corporation are intended for automotive, appliance, underwater cameras, or non-water resistance applications. The connectors have a 5 mm (0.197”) pitch and are available in 2 & 3 circuits. Wire sizes AWG #22 to AWG #18 with either standard
DC/DC Controller Used in Step Up/Down Inverting
November 7, 2008 4:41 am | Product Releases | CommentsOperating over a temperature range of -55°C to 125°C, the LT3724 from Linear Technology is a 60V (65 V max.) low quiescent current (100 µA) switching regulator DC/DC controller used in step-down, step-up, inverting, and SEPIC topologies. A power supply incorporating the DC/DC controller can convert a 4 V to 60 V input supply to a regulated output
Load Cell Includes USB Output
November 6, 2008 10:04 am | Product Releases | CommentsFeaturing a USB Digital Interface with 16 bits resolution, the LSB200 S-Beam Jr. load cell from FUTEK Advanced Sensor Technology is available with USB output option. Available in both aluminum or stainless Steel, the load cell has built-in overload protection. The load cell has weight of 0.3 oz (aluminum) / 0.9 oz (steel)
Air Cars- Next Big Thing or Pie-in-the-sky?
November 6, 2008 9:39 am | by by Jason Lomberg, Technical Editor | Blogs | CommentsWhen we think of advanced technology vehicles, we usually conjure hybrid electric, fuel-cell, and solar cars. But the term, in fact, encompasses a wide-variety of off-the-wall designs including our most fundamental resource- air. Compressed air, as a technology, is nothing new. Seen in everything from power dusters to UPS’s, compressed air has a wide scope of application. But as an ATV variant, compressed air is relatively new (and unproven). French-based Motor Development International (MDI) has, since 1991, taken the lead in creating a viable air-powered vehicle.
LED Protector Features Electronic Shunt Path
November 6, 2008 9:35 am | Product Releases | CommentsProviding a switching electronic shunt path when a single LED in an LED array fails as an open circuit, the PLED 6 Series from Littelfuse is an open LED protector that features a current range of 300 mA to 1.0 A. With an on-state voltage of 1.5 V, the open LED protector uses a 4-layered thyristor structure that automatically resets if the LED heals itself or is replaced and also features
Luminaire Disconnect Suits Fluorescent Fixtures
November 6, 2008 9:22 am | Product Releases | CommentsAdding to the 873 LUMI-NUTS product line, WAGO’s 873-903 3-pole luminaire disconnect targets linear fluorescent fixtures that use a dimming circuit or the Digital Addressable Lighting Interface (DALI) protocol. The power input/line side accommodates AWG #18-12 solid and AWG #16-12 stranded conductors, and the ballast/load side accepts AWG #18 solid conductors. The component presents a current rating of 6 A at 600 V, a UL94V-0 flame-rated
Cameras Contain Gigabit Ethernet Interface
November 6, 2008 8:20 am | Product Releases | CommentsTargeting industrial inspection, general machine vision, and microscopy, Prosilica’s GS Series periscope-type CCD cameras present a gigabit Ethernet interface (GigE vision) to allow cable lengths of up to 100 m using conventional network cables and up to tens of km using fiber optics. Functions consist of snapshot/globalshutter, pixel binning, area of interest readout, external
Digital Delay Generator Exhibits 10 ns Edge Resolution
November 6, 2008 6:58 am | Product Releases | CommentsHaving 8 timing channels with programmable logic, Berkeley Nucleonics’ Model 725 multi-trigger digital delay generator demonstrates edge resolution of 10 ns. Up to 8 trigger inputs can be logic signals, switches, transducers, interlocks, sensors, computer commands, and
Resistors Show Wide Resistance Range
November 6, 2008 6:18 am | Product Releases | CommentsOffering sizes from 0402 to 2512, Stackpole Electronics’ HGC Series thick-film chip resistors exhibit resistance values from 1 KOhm to 2 TOhm. The components present tolerances from 20% down to 0.25%, TCRs ranging from 200 ppm down to 25 ppm, and VCR characteristics of <1 ppm/V. Applications include voltage drivers for test instruments, meters, and
Step Motors Suit Multi-axis Apps
November 6, 2008 5:35 am | Product Releases | CommentsBased on the MotionChip DSP control technology, Technosoft’s IS23x-MA intelligent step motors adapt to distributed motion control applications with integrated intelligence. The 61 mm to 96 mm × 57 mm × 57 mm units embed a stepper motor, power electronics, a controller, and an interface with basic local digital and analog I/O signals, and PLC functionalities. The ready-to-run steppers offer permanent output torque from 1 Nm to 1.8 Nm, a single power supply from 12 V to 48 V, and high resolution
Controller ICs Target Capacitive Touch Apps
November 6, 2008 4:07 am | Product Releases | CommentsAdding to the PureTouch family, Leadis Technology’s LDS6003, LDS6005, LDS6023, LDS6025, and LDS6028 touch controller ICs perform in mobile and non-mobile capacitive touch applications. The 0.8 mm thick components operate at 1.8 V with power consumption of <200 µW, Strongest Touch Selection (STS) for inadvertent touch prevention; Threshold Individually Programmed (TIP), and Automatic Ambient Compression (AAC) for environmental response
LED Lighting Creates Beam Angles
November 5, 2008 11:17 am | Product Releases | CommentsPowering via a 24 VDC Class 2 power supply, DDP’s Emerge LED CoveWash customizable linear LED lighting utilizes a linear parabolic reflector and thin-film diffusers to create various beam angles. The Energy Star-compliant product consumes 3 W/ft while providing upwards of 145 lm/ft and efficacy of 40 lm/W when combined with DDP’s SSLD technology. The UL-certified lighting
Temperature Controllers Use Dual LED Display
November 5, 2008 10:47 am | Product Releases | CommentsAccepting a variety of thermocouple and RTD inputs, Omega Engineering’s CN740 Series 1/16 DIN temperature controllers show process value and set-point value simultaneously on a dual LED display. The CE-compliant products offer single output control, either simple ON/OFF or full PID, two alarm outputs, and indication of auto-tuning, engineering units (°F or °C), and alarm status on
Motherboard Utilizes Quad Processor
November 5, 2008 10:15 am | Product Releases | CommentsPossessing the Intel Q45 Express chipset with Intel I/O controller hub 10 DO, ITOX’s EL330-DR micro-ATX form factor motherboard supports the 45-nm Intel Core 2 Quad processor Q9400 with up to 6 MB of shared L2 cache and up to 1,333 MHz front side bus (FSB). The component protects against software-based attacks, and safeguards the confidentiality and integrity of data stored or created on an embedded system via Intel Trusted Execution Technology (TXT) support. The device integrates
DC/DC Converter Delivers 3.3 VDC
November 5, 2008 9:33 am | Product Releases | CommentsUsing 200 LFM airflow, Power-One’s SSQE48T25033 sixteenth-brick DC/DC converter supplies 3.3 VDC at 25 A with 100% of full-rated power available at 55°C and 22 A at 70°C. The 22.9 mm × 33 mm × 9.5 mm devices offer ±3% combined line, load, and temperature regulation; efficiencies of up to 93%, an input range from 36 VDC to 75 VDC, the capability to
